سلسة السيرفس برقم الميكرو - TV فادي

سلسة السيرفس برقم الميكرو - TV فادي

8821CPNG-5EE1, 8821CPNG-4CN8, 8821CPNG-4GD9, 8821CPNG-4U88, 8821CPNG-4RJ1, 8821CPNG-4JB2, 8821CPNG-5CV5 - see chassis M28.
8821CPNG-4UD4 - the entrance to the service:
1.kanal 30
2.kanal 88
3.gromkost at least. (-VOL)
4.MUTE

8851CPNG - see chassis M28.

8891CSCNG6V12
1. TV on your keyboard to adjust the volume on 0, keeping the "VOL-" to press DISP (rectangle-plus) on the remote.
2. The entrance to the service - press the button on the button "MENU", "CH" - and enter the code 2483 or 6483 or 6568.
3. Hidden button FACTORY (located under the button PP)

8897CSBN - see chassis ETE-2.
8897CSBNG-6PR4 PA-09 - see chassis M28.

percent. 8821CPNG4UD4
The entrance to the service:
1.kanal 30
2.kanal 88
3.gromkost at least.
4.mute

percent. 8821CPNG5EE1, 8851CPNG6N59, 8891CSBNG6N54
Log in servic:
on the local keyboard to adjust the volume to 0, hold VOL DOWN press DISP (rectangle-plus) on the remote.

percent. 8873CSCNG, 8873CPANG
Log in servic:
on the local keyboard to adjust the volume to 0, hold VOL DOWN press DISP (rectangle-plus) on the remote.

percent. 8891CRCNG7D11
Press the remote button "MENU" to enter the "TUNING", press the "CH-"
Select "TARGET POS", enter "2483", "6483", "6568", TV will go into AGING mode.
In the "factory" mode or "AGING" mode, press the button "SYS", "SOUND", "SLEEP" to adjust the data on screen
is menu + factory. Press the "MENU" to enter the main menu.
Press the "DISP" to exit, the screen shows only the inscription "factory".

CXP85340, CXP85452-135S, CXP86441-509S, CXP86441-533S - see LG.

DW5255M, DW370M - see DAEWOO model 14A5 or KR21N7N.
GS8114-01B - Deactivate LOCK ON: Code for remote MAC-2000 - "1123".
1. The button "MENU".
2. The button "OFF" button with "Shift".

LA76931 - see LG.
LA76936, LA76938 - see chassis SA-A.
LA76936DE - see SANYO Chassis AC6-A.
LA76936Y, LC863532C, LC863hhh, LA768hh (05, 10, 12, 18, 28.32) (A) - TV controllers in many different chassis (eg, 3Y01) - versions of the entrances to the service mode:
1. - On the remote press the secret button LC863320A, LC863324A, LC863328A, LC863332B FACTORY (or PROD), it may be below the button SLEEP. It is also possible to close pins 2 and 13 (2 and 14, 2 and 15, 2 and 16) chip on the remote.
2. "Volume" at least at the same time press and hold the button for a while "VOL-" on TV and "RECALL" (DISPLAY) button on the remote. Press the "Timer", "MUTE" - a menu selection.
3. Press the button on the "SKIP", "VOL-", "AFT" [/ color] (or [color = darkblue ]"-/--"). The button "PIC" - a way out.
4. On the remote press (MENU) (MENU) (V. WIEV) (MUTE) (SLEEP). Button TIMER "- the transition from menus.
5. LC863320A-panel FUNAI MK11, LC863hhh LA768hh + (05, 10, 12, 18, 28.32) (A), Samsung SM14H4MJ - LA76936Y 7N-58T7 on the remote to close pins 2 and 16 chip RT2461-103 remote control. For the first time - on the screen FACTORY. 2nd time - on the screen: B / W ADJUST (regulirovka. modes tube). 3rd time - ADJUST (geometry). 4th time - SETUP (installation options). The fifth - out of service
Buttons P and P +; Vol-; Vol + help to establish the appropriate values ​​in the right places.
Important! In the ADJUST MENU SETUP SELECT parameter set to "1", with open sections 00 - 20.
6. LA76931, LA76936, LA76938 - the same processor SDA5522.


LC863332B 52Z6 3KD0, LC863532C-55P9, LC863532B-53l1, LC863532B-54R6, LC863532C-55K9 - entry into the service menu by pressing the remote install "VOL-" to 0, then the main menu (or PICTURE MENU) to enter the code: 8 or 6 0 0 8 6 3 3, or 6 4 8 3 (call it XXXX), which is equivalent to pressing the FACTORY.
The service mode comprises 3 units: FACTORY, B / W BALANCE, ADJUST. Switching between them after pressing the Factory, or by entering the code XXXX.
The service menu is recommended to set ENG.OPTION = 1, SETUP SELECT = 1.
Exit this mode in two ways:
1. After pressing the buttons on the remote "MENU" to enter the code XXXX, get into the mode of "PRODUCT", then repeat the operation (after pressing the "MENU", enter the code XXXX), to return to normal.
2. Set the MENU option in 03 "PROD MODE" = 0, and then press "MENU" to exit the service menu.
To remove the lock:
The first option - press and hold the remote button "DISP" for 10 seconds
The second option - on the remote press the "CALL" and hold for a minute.

LC863332B, TDA9381PS/N2/1I1150, TDA9381PS/N2/1I1246.
The entrance to the service menu: Turn on the TV to normal operation on the remote control button press sequence "POWER", "MUTE", "CALL", "TIMER", "appears on the display FACTORY. KnopkuTIMER Press", "will open the first line of the menu Balance white. Go to the next line is carried out with the remote buttons "CH", change the digital value bytes - buttons "VOL +/-".LC863528A-xxxx - entry into the service menu: press "REWIEW", then "VOL-" and simultaneously "REWIEW". To exit, repeat the procedure.

Log in to service LC863328-5W63, Mak maXim code 1 3 7 9 press VOL-on TV to 0, and Title on the remote.

LC863440W-52F2 Service, for the lazy: Press MENU on the remote control at the same time and VOL + on the panel.


LC863548B, chassis PAXX0081.Vhod in servic: on the front of the TV set volume to 0, hold "VOL-" to press "DISP" (rectangle with plus) button on the remote.

LG8993-08B, LG8993-09B, LG8734-01E,, LG8738-05C, LG8993-13D, LG8993-37B, LG8818-19A, LG8991-04B See LG.

The control unit based on a microcontroller LT01D 51KC - one of the latest developments.
ZiLOG.
Enter the service mode is possible in two ways.
The first way is to click the remote service FACTORY.
The second way: switch off your TV into standby mode on the remote control RC0201 press MUTE and
switch on the TV to normal operation.
Appears service menu has the following form.
BUS CONTROL
SUB ADJUST
H-V ADJUST
W-B ADJUST
BIT ADJUST
Movement in the service menu made with the remote control keys «CH», «CH».
Tincture of parameters. Remote control keys «VOL», «VOL».
1.1. Setup menu SUB ADJUST.
Setting Values
default
Range
Description of parameter changes
SUB COLOR 0-18 6 Preset Color
SUB BRIGHT 7 0-18 Preset brightness
SUB
CONTRAST
11 Preset 0-18
Contrast
SUB TINT 0-18 9 Preset
NTSC hue
SUB SHARP 9 0-18 Pre-definition
AGC ADJUST 19 0-63 The setup AGC
CDL ADJUST 3 0-7 Max. level of video
signal at the cathode
VCO ADJUST 112 (38.0MHz)
80 (38.9MHz)
0-127 Installation of IF
1.2. Settings in H-V ADJUST.
Setup,
Description of the parameter setting range changes
H-SHIFT 40 regulates. phase 00-63
V-SIZE 20 Vertical Size 00-63
H-SIZE 00-63 32 Not used
COR-PIN 32 not used 00-63
V-SLOPE 38 Image Center 00-63
V-SHIFT 32 centering on the vert. 00-63
H-PIN is not used 32 00-63
H-TARP 32 not used 00-63
V-ZOOM 36 not used 00-63
V-SCR 7 Vertical Linearity 00-63
1.3. Setup menu W-B ADJUST.
Setting range of changes
VSD tincture accelerating
voltage
R 32 00-63 red
G 32 00-63 green
B 32 00-63 blue
1.4. Setup menu BIT ADJUSTMENT.
LAST POWER OFF turn on the TV in the operating mode button "Net"
TELETEXT OFF ON / OFF. teletext mode (not used)
16:9 OFF Not used
VIDEO 2 OFF ON / OFF. additional video input
LANGUADE ALL ON ON / OFF. menu languages
ARABIC ONLY OFF Not used
1.5. When finished, press the button on the remote control «MENU», to exit from the service
treatment and storage of data.

M37102M8-C41SP, M37204MC-A49SP, M37201M6-C435SP, M37221M6-066SP, M37204MC-C40SP, VCT6743G B3 08 - see the JVC.
M37160M8-058FP/M37160M8H-051FP or M37160M8-063FP or M37160M8-064FP. The entrance to the service menu - the main menu, enter the code: 6 4 8 3, which is equivalent to pressing the FACTORY.
The service mode comprises 3 units: FACTORY, B / W BALANCE, ADJUST. Switching between them after pressing the Factory, or by entering the code 6 4 8 3

M37201E6-E8WW - see SANYO chassis A8-B.

M37221M4-322SP - see chassis M11D.

MC144105 - see chassis GRUNDIG CUC5301.

NTDA9381/C340AG - the entrance to the service menu:
press the button on the "MENU", 8, 5, 0, 0.OM8363H/n3/4 - see SANYO.

QXXAVC305P, QXXAVC568 - see SANYO Chassis AC6-A.

SAA5290ZP/033, SAA5290, SAA5563PSM30053 - see SANYO.

SAA5297PS/262 - see ORION 28BDF TV790, chassis 4400.SAA5531 SAA5541:
Log into the service menu offers two different ways:
1. Turn on the TV to normal operation and at 0.25 seconds to close the connector X760.
2. Turn on the TV to normal operation, at the service panel to press SERV ", hold the press!" "(The board staff control of IC1 closed conclusions 3 and 9, 1 and 15, respectively). Moving into the service menu made from the control keys" CH-"," CH ". Tinctures parameters are the keys" VOL-"," VOL + " . Using the remote key "0 ... 9 ", you can select the desired sub-menu. After installation is complete to exit the service mode and save the data press the button on the remote TV (1 and 9 are closed conclusions IC1).
Removing the LOCK mode: If the forgotten confidential code in the "Function" select "Lock" button on the remote and hold "X" button for 3 seconds.

SAA5531PS/M4/0329, SAA5531PS/M4/0330, SAA5531PS/M4/0657 - see chassis CTS-AA, CTS-AB.
The control unit based on a microcontroller SAA5531/CTV832R. This system can be
used with all international standards television. In this system, all existing
management functions are displayed on the screen as a menu. All image adjustments
controlled via I2C.
The microcontroller can have built-in teletext decoder.
1.1. Enter the service mode is possible in two ways:
a) Insert the chassis in the operating mode and 0.25 seconds to close the connector X760.
b) Insert the chassis in the operating mode on the service remote control press «SERV»,
holding it, press the «» (on board the remote control at normal m / c closes IC1 findings
3 and 9, 1 and 15, respectively).
1.2. Movement in the service menu made with the remote control keys «CH», «CH».
Tincture of parameters. Remote control keys «VOL», «VOL».
1.3. Using the remote control keys "0 - 9" it is possible to select the desired menu item:
0. installation of the inverter 5. adjustment of hue
1. AGC adjustment 6. setting the delay
2. vertical size 7. installation options
3. correction setting screen 8. setting the tuner
4. Vertical alignment 9. initialization CTV832 PRO
1.4. When you configure a channel to set the following parameters:
IF. 38,9 (38,0)
IFL1. 33.4
IFOF. 32
AG. 19
1.5. Setting the geometric dimensions:
HSH. phase adjustment
VS. Center of the image
VA. setting the size of the vertical
VSD. tincture of the accelerating voltage * (when installing the brightness in the middle position,
accelerating voltage regulator to establish a weak luminescence band)
VSH - Vertical alignment
SC. linearity in the vertical
EW. not used
PW. not used
CP. not used
TC. not used
1.6. Setting the color tone:
WR. red
WG. green
WB - Blue
1.7. Check the installation of bytes and options: 1.8. Check the installation modes
of the tuner:
BITS. 47 TSL. 045
OSD - 0 TEL. 153
OP1. E3 TSM. 153
OP2. 05 TEM. 428
OP3. 28 TSH. 428
OP4. FB (F0. For S0401) THE. 863
OP5. 05 TBL. 01
OP6. 04 TBM. 02
OP7. C1 TBH. 2C
1.9. When finished, press the button on the remote TV (1 and 9 are closed conclusions IC1),
to exit the service mode and save the data.
1.10. Installing the package TV LOCK.
In cases when confidential forgotten the code in the menu "Function" select
"The Castle" and hold the button for 3 seconds «X» in the remote. Mode "Lock" to a state
OFF.


SDA2080, model FT7172B, FT7173, FT7174, FT7176, FT7182, FT7185, FT7186, FT7188, FT7191 TV UNIVERSUM and QUELLE - to enter the service mode is necessary for a short time to press the button N1, N2 or N3 in front of the TV or press the button " P / C "no remote and no less than 8 seconds, hold down the button on the front of the TV, hidden in a small hole on the left, to the left of the three buttons on the TV set channels.

SDA30C164 - see PANASONIC Chassis EURO-3.
SDA3526 - see chassis GRUNDIG CUC1835.
SDA5255-A023 - see
DAEWOO 14A5
SDA555XFL - see LG.
The control unit based on a microcontroller SDA555XFL-one of the latest developments
. INFINEON Technologies. with built-in teletext decoder (up to 10 pages) and powerful
generator OSM on board, TVText Pro.
1.1. Enter the service mode is possible in two ways.
The first way is to type with a remote control code "062 596. MENU.».
The second method is to enable the chassis to the operating mode, the remote service press «» (in
board in the usual remote m / c closes IC1 pins 1 and 15).
Appears service menu has the following form.
SERVICE (02)
PRESET
WHITE BALANCE
Geometry
TSVETOTEPLOTA
TEST RGB
AVTOPDSTROYKA
TIME HOUR = 00000
1.2. Movement in the service menu made with the remote control keys «CH», «CH».
Tincture of parameters. Remote control keys «VOL», «VOL».
1.3. Setup menu PRESET.
Setup, description of the parameter
AGC 17 AGC Settings
IF-PLL 38.9 Installing the IF
TUNER 1 (2) Tuner Type DT5 (KS-H-134)
OSD 1,0 V * Brightness graphics
TXT 245 KB teletext
TXT2 096 bytes teletext
1.4. Settings in the white balance menu.
Setup, description of the parameter
R 31 * Red
G 31 * Green
16
B 31 * Blue
C LEV 3 Max. level of video signal at the cathode
S BRT 6 Preset brightness
Tincture of the accelerating voltage VSD **
*- Parameter settings that are changed when configuring the TV.
**- When setting brightness in the middle position, the regulator of the accelerating
voltage to establish a slight glow strips.
1.5. Settings in geometry.
Setup, description of the parameter
SBL 00 *
V SLOPE 31 * center of the image
V SHIFT 31 * Alignment of vert.
V AMP 31 * Vertical Size
S CORR 31 * Vertical Linearity
H SHIFT 31 * Adjustable. phase
*- Parameter settings that are changed when configuring the TV.
1.6. Setup menu TSVETOTEPLOTA.
Setup, description of the parameter
WARM R 10 Red
WARM 00 G Green
B WARM -08 Blue
R COLD -08 Red
COOL G Green 00
COOL B 10 Blue
1.7. When finished, press the button on the remote control «MENU», to exit from the service
treatment and storage of data.
1.8. Installing the package TV LOCK.
If forgotten confidential code, enter twice universal code
Access, "0711."

SDA5521 - see chassis 12.5.

SDA5522 - the entrance to the service:
1. press the button on the MENU.
2. three times to press on the remote RECALL.Perebor pages - click MENU, exit - RECALL.
To release the lock in these chassis - press and hold the DISPLAY (RECALL) button on the remote for 10 seconds.

ST6-ELAME2 - to enter the service menu press the buttons on the series: "SKIP", "VOL-", "FINE TUNE". To exit, press the PIC.

ST6387B1 - see SHIVAKI STV-102.
ST92195 - first go to the main menu, then press the button on the 4, 7, 2, 5. Parameters selected button "PROGRAM UP" "PROGRAM DOWN", and change settings - "VOL-", "VOL +".

ST92195C7B - the entrance to the service menu:
1. Log in MENU
2. Activate FUTURE
3. Enter code 1923
ST92R195 - see SANYO chassis EB-6A.

STV92195 (TXT) or STV92185 (NO TXT), CTE-chassis AAVhod the service menu - install "program 75", press "OSD" button on the remote and "MENU" on the front of the TV, hold about 4 seconds. "S" symbol appears in the lower left corner of the screen.
Exit Service Mode: - turn off the TV.

TCL-A19V01-TO 87CP38N-4GD1,
TCL-M13V TMPA8809,
TCL-A25V02-T0 8857CRNG5FF4,
TCL-A30V02-TO 8821CRNG5JB2 - see chassis M113, M17, M28.

TDA12020H/N1F00 - see SANYO Chassis FB1-B.

TDA9341 - on the remote to quickly press the button "MENU" "6" "4" "8" "3". Jump to service menu numeric keys 1 .. 4. Output - Power OFF.

TDA9345PS/N3/3/1913 - see BEKO chassis E1.

TDA9350PS/N3/1I1515 - entry into the service menu - switch the TV on 75 programs simultaneously Press "Display" button on the remote and "Select" on the front of the TV.

TDA9351PS/N3/3 DTA1489 586E - entry into the service menu: press on the remote control: MUTE, CALL, - / -, CALL, MUTE. Output from the service - click EXIT.

TDA9351 / TDA9381 (optional) - Enter the service mode is possible in two ways:
1. Enable TV to normal operation, at the service panel to press «SERV», holding it, press the "?" (The board is the usual control of IC1 closed conclusions 3 and 9, 1 and 15, respectively).
2. Insert the chassis in standby mode, press the remote to the usual sequence of keys «STATUS», «MENU», «MUTE», «STBY». A service menu. Moving in the service menu made from the control keys «CH», «CH». Tincture of parameters - control keys «VOL +», «VOL-». The transition from the submenu on one level - key AV / TV ». Information Bar "Key" displays the value of the password entered in the user menu.

TDA9351PS/N2/3I, TDQ935XPS/N2, TDQ936XPS/N2, TDQ938X/PS/N2 (CH05T0102)
TDA9351 48K PAL / NTSC / SECAM a PAGE TELETEXT
TDA9350 48K PAL / NTSC 1 PAGE TELETEXT
TDA9361 64K PAL / NTSC / SECAM 10 PAGE TELETEXT
TDA9360 64K PAL / NTSC 10 PAGE TELETEXT
TDA9380 32K PAL / NTSC
TDA9387 32K NTSC, landing gear EX-1A4 - set volume to 0. Then press and hold the MUTE button on the remote and press the "MENU" button on the TV.
To exit the "S" mode off TV.

TDA9361PS/N3/5 CF6843 54,607,130 - the entrance to the service: Press the button on the "MENU" button and enter code 6483.
TDA9363 TDA9381 TDA9384.Variant 1. controller TDA9384/TDA9363: Press MUTE, CALL, 9, has a light up "9 - -", then press "8", "0" should appear the inscription "M". Press "MENU" to enter the service menu. Button CH + / CH-click, V + / V-to change.
Option 2. controller TDA9381: press and hold the button for 4 seconds "QV", then press the button on the "MENU1", the screen should light up the inscription "TEST" When you click the numbers "Mkey" appear on the screen corresponding to a submenu, or sign PASSWORD, then you need to enter password 828 .. Button CH + / CH-click, V + / V-to change. Disabling the remote control the TV on in standard mode.

TDA9365PS/N3/5, TDA9352PS/N3/1/1683, TDA9565, TDA9352PXN.
Log: "St-by"> "MENU" on TV + "0" on the remote. Exit> "TV".

TDA9370PS/N3/A TSG 0430 3 Eeprom: 24C08.Vhod in service "uncivilized": the programmer to register a cell 1D1-FF, when you turn the machine is in service mode.
1.8 Use selected menu page. Exit - click "I". Memorizing is done automatically. In the absence of the original remote, you can use the MAC code 1264.
TDA9380PS/N1/1K0231 - the entrance to the service:
Simultaneously press the button on the remote control teletext "CLOCK" and "VOL-" on local keyboard. After 2-3 seconds the TV will enter into Service Mode.

TDA9381/C346BG - entry into the service menu in the main menu, enter the code: 6 4 8 3.

TDA9381-7NA - press button on the "MENU" "8", "5", "0", "0". The choice of options - buttons 0 - 9. You must enter a group number of options, with the first available option groups 3, 4 and 5. If you try to call other options appears on the screen lock. You must enter the code "200 528", then there is the invitation PRESS MENU NUMBER. To remove the code "lock" to hold more than 5 seconds LOCK key on the remote and turn off the menu code. In all programs "1 ... 0" should be removed locking (mandatory at all!)
Instead of the standard remote control, you can use MAK-2000, code 1172. ERASE button displays the TV directly into the service menu, and then also use the numeric keys and the "P +", "P-", "Vol +", "Vol-". Out of service - click ERASE or STBY or TXT - three clicks .

TDA9381PS/N2/1I0721 TDA9381PS/N2/1I0836 TDA9381PS/N2/1I1156 TDA9381PS/N2/1I1520 TDA9381PS/N3/1/1729Dlya Log in to service in the standby mode press the "menu" on the front of the TV and the "0" on the remote .
To store the settings, press the "TV" and hold off on the TV network
Removing the lock: enter the Options menu, select Chateau, dial "2", "2", "white button".

TDA9381PS/N2/3I0792 OICTMPH010A.
On the remote RC-5 closed 1.11 conclusions SAA3010. Switching pages service - "Q. VIEW" panel TV. "OK" - to remember.

TDA9381PS/N2/3I DTA1481 "Y" D621 - the entrance to the service:
close the short circuit panel findings 18-24 JKT T3833-02G.

TDA9381PS/N3/3 P26NG - on the remote press the "2". after the press six times "P-", "V" button to hold for 10 seconds, you will service menu. Exit - "DISPLAY".

TDA9384PS/N3/3, TDA9384PS/N2/3I - see chassis 3P51.

TMPA8851CPNG-6EG1, undercarriage TD173.Vhod in servic: on the front of the TV set volume to 0, hold "VOL-" to press "DISPLAY" (rectangle with plus) button on the remote.

TMPA8821CPNG-4UD4 - the entrance to the service: 30 channel, 88 channel, Volume - 0, MUTE.
TMPA8821CPNG-5EE1 - see chassis M28.

TMP47C1637 - see PHILIPS chassis GR2.2AA.
TVP02066 D05 \ 04 - see AIWA 1402.

VCT3831A entry into service: press "MENU", then press RECALL five times. Further buttons 1 ... 9 are caused by various service menus.
Output from the service or the 0 RECALL.

VCT6743G B3 08 - see the JVC.